This document was based on version 3.1, but you'll want to make sure you have the latest version from here.Ĭorrects an error about a method of disabling the bank angle limits. #MODEL BUILDER SOFTWARE SOFTWARE#Note that MUST have a current version of the SPS software to do this. It will help you get the SPS software installed and get your receiver connected for the first time. If you are not at all familar with the SPS software, then I'd suggest you start with the walkthrough in the above post first, even if you don't want to make any changes that way. To use my SAFE Model Builder program, see post # 4 below. #MODEL BUILDER SOFTWARE HOW TO#The document in this post is a walkthrough for how to edit settings for SAFE features by editing the text file directly. Have SPS load the changes into the receiver. OR, use my SAFE Model Builder program to help you make those changes and save the file.ĥ. Use a text file editor to read the file, type in strategic changes, and save the file. Have the SPS read the settings in your receiver.Ģ.Ğxport those settings to an SRM file, which is a text file.ģ. In a nutshell, this is the process for making those changes:ġ. In October 2017, there was a revelation in the "E-Flite SAFE RX In Another Plane Thread"! It was discovered that you could edit a lot more settings inside the AR636 configuration for a SAFE Select receiver if you went above and beyond the capabilities of the Spektrum Programmer Software (SPS). See the next post (# 2) for how to change the Mounting Orientation and the settings directly related to SAFE features. #MODEL BUILDER SOFTWARE PC#Their YouTube playlist is here:Īt the time of this writing, only the PC software recognizes SAFE Select receivers the phone app does not.Ĭhanging the SAFE Features SPS Cannot Change #MODEL BUILDER SOFTWARE SERIES#Spektrum made an excellent series of videos when the AR636 first came out, and even though they use the phone app instead of the PC software in the videos, all of the explanations apply the same way. It's not an exhaustive explanation of all of the various settings available. This document is a basic walkthrough for how to get the Spektrum Programmer software running on a PC, connect a receiver, and make changes on the SAFE Select receivers. Because the receiver needs to move the control surfaces in the correct direction, those are very important settings on the receiver! The Surface Setup can be changed on SAFE Select receivers, but the Mounting Orientation cannot be changed using SPS. #MODEL BUILDER SOFTWARE INSTALL#Also, SPS does not have screens to modify the SAFE features (self-level, panic, etc.) There are two key areas of most interest if you want to install a SAFE Select receiver in another airplane - the Mounting Orientation and the Control Surface Setup. Not all of the settings in the Spektrum Programmer software apply to SAFE Select programs. This was step one in the process of learning how to work with SAFE Select receivers. This first post talks about some of the basic things you can - and cannot - modify using SPS alone. It explains how SAFE works, and it also explains one of the most important aspects of this process - how to test your airplane on the ground to make sure the receiver is working correctly. It's a combination of the documents in posts # 3 and # 4, along with some information from the process of installing an Apprentice S SAFE receiver in another plane. If you have never installed a receiver with SAFE in another airplane, or you're new to SAFE, I encourage you to check out the Ultimate Guide to Installing an AR636 with SAFE in post # 6. Post # 5 contains some model setup files (SRM files) that provide a good starting point for configuring your own SAFE model. That has been replaced with the program in post # 4. The information in post # 2 is an "old" way of manually changing the SAFE settings inside a text file that comes from SPS. Although Spektrum still hasn't provided all of the tools to fully configure the SAFE features on an AR636 receiver, I've brought a lot of information together and developed a programming tool for SAFE with an AR636. The information in this thread has evolved quite a bit since it was first opened in June 2017. Prior to SAFE Select, the programming on SAFE receivers was completely locked out despite the fact that the AR636 is normally programmable from a phone app or the PC software. SAFE Select is based on the AR636 receiver, which has proven to be very versatile for a number of applications based on the way it's programmed by HH.Ī feature that was new with SAFE Select is the ability to adjust at least some of the settings in the AR636 using the Spektrum Programmer software (SPS). In 2016, Horizon/Spektrum introduced "SAFE Select", a new variation of their beginner-oriented SAFE stabilization system.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |